Hand Knitted Scarf Sweater Hat Socks

48 Needle Knitting Machine (Inner Diameter Is About ≈26cm/10.24inch) Select Picture 2: 48 Needle Knitting Machine + Box + Yarn（Uit With Yarns）

Note:(48-Needle Knitting Machine Suit Selection) Uit With Yarns-Suit Without Yarn

Select Picture 1: 48 Needle Knitting Machine + Packing Box（Suit Without Yarn）

 Select Picture 2: 48 Needle Knitting Machine + Box + Yarn（Uit With Yarns）

40 Needles - Knitting Machine +Packing Box, Package Included As Below：

1 X 40 Needles Knitting Machine
3 X Plastic Sewing Needle
1 X Crochet Hook
1 X Screwdriver
1 X English Instruction Manual
1 X Packing Box

40-Needle Knitting Machine Is Suitable

40 Needle Knitting Machine (Inner Diameter Is About ≈22cm/8.66inch)

22 Needles - Package Included:

1 X 22 Needles Knitting Machine
2 X Bundles Of Yarns (Random Colors Delivery)
1 X English Instruction Manual
1 X Crochet
1 X Short Needle
1 X Packing Box

22 Needle Knitting Machine Is Suitable:

22 Needle Knitting Machine (Inner Diameter Is About ≈10cm/3.94inch)

22 Needles - Package Included:(Inner Diameter Is About ≈10cm)

1 X 22 Needles Knitting Machine
1 X Plastic Sewing Needle
1 X Crochet Hook
2 X Bundles Of Yarns (Random Colors Delivery)
1 X English Instruction Manual
1 X Packing Box

22 Needles - Package Included:(Inner Diameter Is About ≈10cm)

1 X 22 Needles Knitting Machine With Row Counter
1 X Plastic Sewing Needle
1 X Crochet Hook
2 X Bundles Of Yarns (Random Colors Delivery)
1 X English Instruction Manual
1 X Packing Box Click On The Picture To Buy

Hairball Making

Click On The Picture To Buy 

Hand Knitting Machine Operation Manual

Figure 1 

1-Inlet 

2 - Crochet (48 Crochets Total) 

3-Handle 4- Odometer

4- Odometer 6-↑Up: Flat Sheet Weave

6-↑Up: Flat Sheet Weave 

↓ Down: Ring/Tubular Braid 5- Elastic Controller

5- Elastic Controller

Small Paste Before Weaving:

Once There, Loosen Or Tighten The Yarn. If You Use Too Fine Wool,

Pass The Thread Continuously Through The Thread Holes On The Two Tensioners, If You Are Using Finer

Pass Through Three Wire Holes In A Row. (See Schematic Diagram Iv-A For Details).

Loosen And Lay It Loose On The Floor Or Table To Prevent Knitting

During The Process, The Yarn Entering The Machine Is Not Smooth.

The Suction Cup Is Installed. Then Place The Machine On A Flat Tabletop. Otherwise, The Machine Will

Affect Your Knitting Effect By Swaying Or Moving During Use.

The Bottom Direction Of The Needle Is Pushed Backward.

Pass It Through The Appropriate Thread Hole On The Slack Adjuster And Then Into The Thread Entry Groove On The Machine. Otherwise,

Your Knitting Will Have Needle Drop.

If The Thread Is Pulled Too Tightly, Please Try To Adjust The Thread Entry On The Thread Hole Of The Tensioner

Location Or Method.

The Yarn Work Is Tighter In The Knitting, Which Will Cause More Effort When You Shake The Handle Of The Machine,

At This Point, All You Need To Do Is Slow Down And Shake The Handle Evenly To Continue.

Ring/Tubular Braid:

Step 1: Tubular Or Flat

Sliding Switch On The Side Of The Machine: T (Down) For Loop/Tubular Braiding, Additionally,

P File (Up) Is Used For Flat Fabric Knitting (Fig.-). You Can Use This Mode And Simple Manual

Finish Off To Make Hats, Wallets, And More.

Step 2: Choose The Right Yarn

Thinner Yarns Can Also Be Used On This Machine, But Continuous Threading Is Recommended

Three Holes For The Controller To Make The Weave Work Tighter. Thin Or Soft Wool Is Also Available

Used, But The Effect May Not Be Good. In Addition, It Is Not Recommended To Use Wool That Is Too Thick And Hard.

It Is Recommended To Take A Sample Of Yarn To Try Before Compiling A Piece.

When The Yarn Enters More Smoothly, Into The Machine. If You Are Knitting Directly From The Yarn Bales,

Please Regularly Pull Out The Right Amount Of Yarn During The Knitting Process To Make Sure It Is Loose Enough (Recommended

Pull Out 2-3 Meters Each Time) Otherwise It Is Easy To Drop The Needle. In Order Not To Stretch The Yarn Too Tight,

Please Be More Careful In Knitting.

Step 3: Thread On The Machine

[Scan The Code To Watch The Video: How To Start Knitting?

Step 4: Set The Yarn Tightness

Not Off-Line (As Shown In Figure 2 And Figure 3);

After Tightening The Thread Guide, It Will Sag Naturally. Keep In Mind That You Will Need To

To Adjust The Position Of The Thread Hole Through The Thread Tensioner. Thick And Heavy Wool Is Recommended To Pass Through The Outside

The Loosest Wire Hole (As Shown In Figure 4).

Tightness: Tight/Tightness: Moderate/Tightness: Loose/Tightness: Tightest(For Very Fine Soft Wool)

Step 5: Start Weaving

In The Knitting, Be Very Small To Ensure That No Stitches Fall. Because Of The Initial Circle Effect

Is To Lay The Foundation For The Success Of The Entire Work;

Weaving (As Shown In Figure 2);

Gently Loosen The Yarn Periodically To Enter The Machine From The Bottom Up To Avoid Needle Drop;

Once This Section Is Longer Than The Machine, You Have To Unroll It Without Interruption And Go Down The Middle

Pull Out To Keep It Running Smoothly.

Step 6: Loop Weave Finishing And Off-Machine Steps

Please Stop Shaking The Handle. Special Note: The Yarn Must Still Remain In The Crochet Hook Of The Machine

Until The Fourth Step Of This Off-Camera Process;

For The Ending Of The Work. Pass The Yarn Through The Thread Hole And The Groove Of The Thread Opening In The Slack Controller

Take It Out And Thread It Through A Plastic Sewing Needle. Then Pull The Yarn Vertically (As Shown In Figure 5),

Shake The Handle To Idle The Machine One Revolution Without Yarn:

Pass Through The Thread Sleeve That The Crochet Hook Has Dropped (As Shown In Figure 7 A.B). You Must Complete A Full Circle Of Threading,

Make Sure That Each Thread Sleeve Is Threaded Through The Plastic Sewing Needle To The Remaining Yarn;

Use The Ending Thread As The Stitching Yarn, Use The Stitches You Used To Sew Items, According To Your Own

Creative Edge Stitching Can Be Done;

Make Back Stitches In The Last Few Sleeves (Shown In Figure 8b), And Tie A Knot At The Tail.

The Tail, Pulling It Tight Until The Mouth Of The Cylinder Is Tight. Thread And Knot The Plastic Sewing Needle A Few More Times.

Once You Have Your Mouth Closed, You Can Also Add Accessories Like Hair Balls To The Knots At The Top Of The Piece.

Change Yarn Color Or Wire Operation-Joint:

Knot The New Yarn With The Old Yarn And Make Sure It Doesn't Slip. Cut Off The Excess Thread,

Take The Yarn Out Of The Wire Port And The Tension Controller First (Otherwise The Knot Won't Pass Smoothly

Thread Guide And Thread Hole For Slack Controller). Tighten The Yarn Manually First, Shake The Handle Until Just

The Knotted Part Goes Into The Machine Crochet, And The Yarn Is Placed Into The Thread Guide And Slack Controller

Flat Sheet Weave:

Slide The Mode Switch Button On The Front Of The Fuselage To The Upper Position.

[See Step 3 Scan The Code To Watch The Video: How To Start Knitting?

Reminder: If You Often Have Edge Needle Drop Phenomenon During The Flat Sheet Knitting Process,

Please Confirm If You Have Shaken The Handle Of The Machine Until It Stops Completely,

Change The Direction Again.

How To Make Up A Dropped Needle:

When This Happens, You Can Use The Matching Small Crochet Hook To Make Up The Needle;

Stop When The Thread Is Inserted, And Note That The Hook Where The Needle Is Dropped Is Just Next To The Thread Entry Port.

The Needle Hook At The Needle Drop Position Is Just Raised;

In The Shape Of A Ladder, It Looks Like A Braided Part Connecting The Two Sides;

Thread Sleeve, At This Time, The Thread Sleeve Formed By The Thread Just Passed Through Shall Prevail, And Hook Up The "Ladder".

Another Thread, Pull Up Through The Thread Sleeve. And So On, In Turn Repair The Needle Drop Until It Can Be

Hook The Thread Sleeve Back To The Crochet Hook On The Machine As Far;

"48 Needle Knitting Machine" Suction Cup Fixing Instructions

Tripod*4,

Suction Cup*4,

Screw*4,

Screwdriver* 1.

Shop at iBuyXi.com

✦How to Measure

Bust: measure around the fullest part of your bust, keeping the tape level. Waist: measure around your natural waistline, keeping the tape comfortably loose. Hips: measure around the fullest part of your hips.

Fit tip: between sizes? We recommend sizing up for a relaxed fit, or down for a snug fit.

Shop at iBuyXi.com